Skip to content
TemperancevilleDoor Specialists
Open 24/7(289) 802-2396Open 24/7
Person kneeling with a hand at the base of a gray paneled door that has a black strip along its bottom. — Garage Door Perimeter Weatherstrip, Aurora
A person kneels beside the side track and hinges of a closed sectional garage door. — Garage Door Safety Inspection, Aurora

Repairs · Aurora

Garage Door Perimeter Weatherstrip

With the door closed and the garage lights off, a thin bright line runs down the whole left side of the opening.

Call (289) 802-2396

In plain words

Winter is what wears a perimeter seal out here. Sun and cold cycles harden the vinyl until it cracks, freezing rain glues the fin to the door so the opener tears it, and salty slush sits against the bottom of the jambs and rots the wood the strip is nailed to. One visit deals with all of that: soft wood at the base of the jamb is cut out and replaced, fresh seal is fitted in continuous lengths with the corners overlapped, and the fin is wiped with silicone so ice does not bond to it. The garage stays drier and calmer through the next freeze-thaw season.

Sound familiar?

A length of weatherstrip along the right jamb has pulled away, nails and all, and it slaps against the trim every time the wind picks up. The wood behind it is dark and soft where it meets the floor.

How the visit goes

Garage Door Perimeter Weatherstrip

How the visit goes

Technician on a blue stepladder using a wrench on a black torsion spring bar above a sectional door with small windows.
Technician kneeling at a garage opening, pushing a black rubber seal into the metal jamb, with a red utility knife nearby.
  1. Measuring for the new pieces

    With the door closed, the header is measured across the full width of the opening and each side from header to floor, because openings are rarely the same on both sides. The profile is chosen to match the gap: a wider fin for a door that sits a little back from the stop, a narrower one where the gap is slight, and a one-piece stop where the wood is going. Colour is matched to the trim from a range of standard finishes. The technician also notes whether the existing stop projects far enough to cover the door edge, since a stop set too shallow leaves the fin working alone.

  2. Taking off the old strip cleanly

    The old fin or stop comes off with a flat bar worked behind it a little at a time, so the trim and any brickmould stay intact. Nails are drawn with end-cutting pliers rather than hammered through, staples are lifted, and any old adhesive is scraped back to bare surface. Where the whole wood stop is being replaced with a one-piece vinyl stop, the stop is freed along its length and lifted out, and the paint ridge it leaves is knocked down so the new moulding sits flat. The bare jamb is brushed clean and any loose paint at the edges is removed before anything new goes on.

  3. A look round each season

    The simplest care is a glance four times a year. Close the door, switch off the lights and look along both sides and the header for daylight. Then step outside and check that no length has lifted, that the corners are still tucked together and that the fin is still soft when you press it with a thumb. Cracks, a hard grey surface or a piece that has shrunk back from the door are the early signs. Manufacturers suggest wiping the seal down with a damp cloth a few times a year, and that also lets you feel any change in it.

Garage Door Perimeter Weatherstrip

In the van

  • Utility knife and mitre saw

  • Epoxy consolidant and exterior primer

  • Vinyl stop moulding with integral seal

  • Silicone spray lubricant

  • Flexible vinyl fin seal

Technician in a cap and safety glasses fitting a paneled garage-door section against the track hinges, with a drill on the floor.

Garage Door Perimeter Weatherstrip

What affects the quote

  1. Commercial or oversized openings

    Wider and taller commercial doors often carry an aluminum retainer with a rubber insert or a brush seal, and the material and fitting time differ from a residential vinyl seal.

  2. Fin on the existing stop or a one-piece vinyl stop

    Nailing a new fin to a sound wood stop uses less material than replacing the stop with a one-piece vinyl moulding, which costs more as a part but needs no paint and does not rot.

  3. Weather on the day

    Cold weather means keeping vinyl warm between the van and the opening and fitting each length with extra care, so a winter visit can run a little longer than one in mild weather.

What to have ready

  • Have mice, leaves or water been getting in?
  • Is it a single or double door, and roughly how wide and tall?
  • Is your garage attached to the house, and is it heated?
Call (289) 802-2396

Garage Door Perimeter Weatherstrip: questions

Questions
What should I do before the technician arrives?

Move the car out of the garage or well back from the door, and clear anything stored against the jambs inside and any bins, planters or snow piled against them outside. Leave the door closed so the gaps can be seen as they are. If you have noticed where the daylight, drafts or snow come in, or where the mice appear, be ready to point it out.

Should I choose a fin on the wood stop or a one-piece vinyl stop?

If the wood stop is sound, straight and not buried in paint, a new fin nailed to its face is the simpler choice and keeps the look of the trim. If the stop is cracked, soft or has been painted many times, a one-piece vinyl stop replaces it entirely, needs no paint and cannot rot. The technician checks the stop and recommends one or the other on site.

Will a new seal make the room above my garage warmer?

It can help. Drafts around the garage door cool the garage, and the garage cools the floor above it and the wall it shares with the house. Closing the perimeter cuts those drafts, though how much warmer the garage runs depends on the door's own seal, the ceiling insulation and how the space is heated, not the perimeter alone. A technician can talk through those as separate steps if the room stays cold.

Related services

Garage Door Perimeter Weatherstrip near you

Call(289) 802-2396

Request a visit

Or call (289) 802-2396 · open 24/7